| Peer-Reviewed

Study of Clay Soils, Case of Nomayos-Cameroon: Thermophysical and Chemicomechanical Characterization of Clay Bricks Loaded with 30% Palm Kernel Shell Powder

Received: 1 September 2022     Accepted: 15 September 2022     Published: 11 October 2022
Views:       Downloads:
Abstract

The work presented in this article consists in demonstrating that the mixture of clay from clay soils and palm nut shell powder is possible for the production of raw clay bricks. For that, we have made characterizations of the mixture of the powder of shells of palm kernel and the clay resulting from the argillaceous grounds of Nomayos which was the subject of a publication. Then, we made the bricks with 0% of load and with 30% of load that we had characterized physically, chemically, thermally and mechanically. The results of the physical characterization allowed us to conclude that the density of the material decreases when it is loaded with 30% of palm kernel shell powder but increases and improves the resistance to bending and compression for the same percentage of load. For the results of the thermal characterization, the ATG, the DSC and the DTG showed: for the clay brick, the presence of free water, Kaolinite, illite and Quartz in important proportion affirming that this clay is of the kaolinite type. For the shells, the presence of free water, cellulose, and lignin; for the mixture with 30% of palm kernel shell powder, the presence of both free water, Kaolinite, illite, Quartz, cellulose, and lignin showing the presence of both clay and shells in the mixture. For the results of the chemical characterization, FTIR showed: for clay, the presence of adsorption bands at 2931 cm-1 and 2865 cm-1, absorption peaks at 1554 cm-1, 1494 cm-1 and 693 cm-1 and a peak near 1307 cm-1. For the shells, the presence of intensity bands at 2924.39 cm-1, average intensity of the fine band between 1509.08 cm-1 and 1606.26 cm-1, intensity peaks between 1372.10 cm-1 and 1317.91 then 1239.65-1030.05 cm-1. For the clay-shell mixture, the presence of adsorption bands at 2931 cm-1 and 2865 cm-1 corresponding to asymmetric and symmetric elongation vibrations of the -CH2 groups showing the presence of the clay silane. The peaks of intensity between 1239.65 and 1030.05 cm-1 can be attributed to the -C-O groups of alcohols, Esther, ether, amorphous silica or -C-O bonds of celluloses and lignins showing the presence of the shells in the mixture.

Published in American Journal of Civil Engineering (Volume 10, Issue 5)
DOI 10.11648/j.ajce.20221005.13
Page(s) 191-200
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2022. Published by Science Publishing Group

Keywords

Clay Bricks, ATG, IRTF, Compressive Strength, Flexural Strength

References
[1] Imen, S., & Belouettar, R. (2011). Mechanical behavior of mud bricks reinforced with date palm and straw fibers. INVACO2 International Seminar, Innovation & Valorization in Civil Engineering & Building Materials, (2p-118).
[2] de Chazelles, C. A., & Klein, A. (2003). Transdisciplinary exchanges on raw earth constructions. 1. Shaped, cut or cased earth. Materials and methods of implementation. Doi: https://halshs.archives-ouvertes.fr/halshs-00548079
[3] Chanvillard, G. (1999). Modeling the pullout of wire-drawn steel fibers. Cement and Concrete Research, 29 (7), 1027-1037. Doi: https://doi.org/10.1016/S0008-8846(99)00081-2
[4] Doat, P., Hays, A., Houben, H., Matuk, S., & Vitoux, F. (1979). Building with earth. Alternative and parallel editions. Doi: http://pascal-francis.inist.fr/vibad/index.php?action=getRecordDetail&idt=PASCALBTP8080279395
[5] Guillaud, H., Cope, R., Odul, P., Doat, P., Houben, H., & Verney, P. E. (1986). Scientific and technical approach to the earth material (Doctoral dissertation, CRATerre; CSTB; Ministry of Research and Technology). Doi: https://hal.archives-ouvertes.fr/hal-03162175
[6] Kazmi, S. M., Abbas, S., Saleem, M. A., Munir, M. J., & Khitab, A. (2016). Manufacturing of sustainable clay bricks: Utilization of waste sugarcane bagasse and rice husk ashes. Construction and building materials, 120, 29-41. Doi: https://doi.org/10.1016/j.conbuildmat.2016.05.084
[7] Munir, M. J., Kazmi, S. M. S., Wu, Y. F., Hanif, A., & Khan, M. U. A. (2018). Thermally efficient fired clay bricks incorporating waste marble sludge: An industrial-scale study. Journal of cleaner production, 174, 1122-1135. Doi: https://doi.org/10.1016/j.jclepro.2017.11.060
[8] Javed, U., Khushnood, R. A., Memon, S. A., Jalal, F. E., & Zafar, M. S. (2020). Sustainable incorporation of lime-bentonite clay composite for production of ecofriendly bricks. Journal of Cleaner Production, 263, 121469. Doi: https://doi.org/10.1016/j.jclepro.2020.121469
[9] Hongrattanavichit, I., & Aht-Ong, D. (2020). Nanofibrillation and characterization of sugarcane bagasse agro-waste using water-based steam explosion and high-pressure homogenization. Journal of Cleaner Production, 277, 123471. Doi: https://doi.org/10.1016/j.jclepro.2020.123471
[10] Misse, S. E., Obounou, M., Ohandja, L. A., & Caillat, S. (2013). Use of palm kernel shells as fuel in a scrap metal melting furnace. Journal of Renewable Energies, 16(1), 75-89. Doi: https://doi.org/10.54966/jreen.v16i1.365
[11] De la Torre Chauvin, E. H. (2015). Preparation of activated carbon from oil palm nut shells for gold recovery and cyanide effluent treatment (Doctoral dissertation, UCL- Catholic University of Louvain). http://hdl.handle.net/2078.1/155680
[12] Hidayu, A. R., Sukor, M. Z., Mohammad, N. F., Elham, O. S. J., Azri, N. I., Azhar, M. A. I., & Jalil, M. J. (2019, November). Preparation of activated carbon from palm kernel shell by chemical activation and its application for β-carotene adsorption in crude palm oil. In Journal of Physics: Conference Series (Vol. 1349, No. 1, p. 012103). IOP Publishing. doi: 10.1088/1742-6596/1349/1/012103.
[13] Djomi, R., Meva’a, L. J. R., Nganhou, J., Mbobda, G., Njom, A. E., Bampel, Y. D. M., & Tchinda, J. B. S. (2018). Physicochemical and Thermal Characterization of Dura Palm Kernel Powder as a Load for Polymers: Case of Polyvinyl Chloride. Journal of Materials Science and Chemical Engineering, 6 (6), 1-18. Doi: 10.4236/msce.2018.66001.
[14] Riyap, H. I., Banenzoué, C., Tchakouté, H. K., Nanseu, C. N., & Rüscher, C. H. (2021). A comparative study of the compressive strengths and microstructural properties of geopolymer cements from metakaolin and waste fired brick as aluminosilicate sources. Journal of the Korean Ceramic Society, 58 (2), 236-247. https://doi.org/10.1007/s43207-020-00097-y
[15] Olembe, Y. R., Fokam, C. B., Tchotang, T., Djomi, R., Kenmeugne, B., & François, M. L. M. (2021). Investigation of the Physical, Mechanical and Chemical Properties of the Marrow of Raffia Hookeri. Journal of Natural Fibers, 1-13. https://doi.org/10.1080/15440478.2021.1961337
[16] Huisken, P. W. M., Tchemou, G., Tagne, N. R. S., Ndapeu, D., & Njeugna, E. (2022). Effect of the Addition of Oil Palm Mesocarp Fibers on the Physical and Mechanical Properties of a Polyester Matrix Composite. International Journal of Polymer Science, 2022. https://doi.org/10.1155/2022/3399986
[17] Limami, H., Manssouri, I., Cherkaoui, K., & Khaldoun, A. (2020). Study of the suitability of unfired clay bricks with polymeric HDPE & PET wastes additives as a construction material. Journal of Building Engineering, 27, 100956. https://doi.org/10.1016/j.jobe.2019.100956
[18] Belaid, F., & Chelouah, N. (2020). Study of the influence of Crushed Date Kernels (CDN) additions on the physical-mechanical and thermal characteristics of a compressed raw earth brick (CREB) (Doctoral dissertation, Abderrahmane Mira-Bejaia University). http://hdl.handle.net/123456789/13704
[19] Nshimiyimana, P. (2021). Influence of substitute materials on the microstructure and strength of compressed earth bricks. Academic Journal of Civil Engineering, 39 (1), 144-152. DOI: https://doi.org/10.26168/ajce.39.1.32
[20] Poullain, P., Leklou, N., Laibi, A. B., & Gomina, M. (2019). Properties of Compressed Earth Bricks Made from Traditional Materials from Benin. Journal of Composites and Advanced Materials, 29 (4).
[21] Ouedraogo, M., Dao, K., Millogo, Y., Seynou, M., Aubert, J. E., & Gomina, M. (2017). Influence of kenaf (Hibiscus altissima) fibers on the physical and mechanical properties of adobes. Journal of the West African Chemical Society, 43, 48-63.
[22] Laibi, B. (2017). Hygro-thermo-mechanical behavior of structural materials for construction combining kenaf fibers with clay soils (Doctoral dissertation, Normandie).
[23] Osabor, V. N., Okafor, P. C., Ibe, K. A., & Ayi, A. A. (2009). Characterization of clays in Odukpani, south eastern Nigeria. African Journal of Pure and Applied Chemistry, 3 (5), 079-085.
[24] Mrklić, Ž. & Kovačić, T. (1998). Thermogravimetric investigation of volatility of dioctyl phthalate from plasticized poly (vinyl chloride). Thermochimica acta, 322 (2), 129-135. https://doi.org/10.1016/S0040-6031(98)00479-1
[25] Shanmugharaj, A. M., Bae, J. H., Lee, K. Y., Noh, W. H., Lee, S. H., & Ryu, S. H. (2007). Physical and chemical characteristics of multiwalled carbon nanotubes functionalized with aminosilane and its influence on the properties of natural rubber composites. Composites Science and technology, 67 (9), 1813-1822. https://doi.org/10.1016/j.compscitech.2006.10.021
[26] Benbayer, C. (2014). Nanocomposites based on clay and polymerizable surfactants (surfmers): synthesis and properties (Doctoral dissertation, Université Nice Sophia Antipolis). https://tel.archives-ouvertes.fr/tel-01142111
[27] Qtaitat, M. A., & Al-Trawneh, I. N. (2005). Characterization of kaolinite of the Baten El-Ghoul region/south Jordan by infrared spectroscopy. Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy, 61 (7), 1519-1523. https://doi.org/10.1016/j.saa.2004.11.008
[28] Risite, H. (2015). Polymer/montmorillonite nanocomposites: Role of interactions generated by clay/polymer modification on morphology and structural, thermal, rheological and mechanical properties.
[29] Hongping, H., Ray, F. L., & Jianxi, Z. (2004). Infrared study of HDTMA+ intercalated montmorillonite. Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy, 60 (12), 2853-2859. https://doi.org/10.1016/j.saa.2003.09.028
[30] Belver, C., Bañares Muñoz, M. A., & Vicente, M. A. (2002). Chemical activation of a kaolinite under acid and alkaline conditions. Chemistry of materials, 14 (5), 2033-2043. https://doi.org/10.1021/cm0111736
Cite This Article
  • APA Style

    Hamka Hamka Adolphe Claudel, Djomi Rolland, Mveh Chantal Marguerite, Tchotang Theodore, Touani Chualeu Parfait, et al. (2022). Study of Clay Soils, Case of Nomayos-Cameroon: Thermophysical and Chemicomechanical Characterization of Clay Bricks Loaded with 30% Palm Kernel Shell Powder. American Journal of Civil Engineering, 10(5), 191-200. https://doi.org/10.11648/j.ajce.20221005.13

    Copy | Download

    ACS Style

    Hamka Hamka Adolphe Claudel; Djomi Rolland; Mveh Chantal Marguerite; Tchotang Theodore; Touani Chualeu Parfait, et al. Study of Clay Soils, Case of Nomayos-Cameroon: Thermophysical and Chemicomechanical Characterization of Clay Bricks Loaded with 30% Palm Kernel Shell Powder. Am. J. Civ. Eng. 2022, 10(5), 191-200. doi: 10.11648/j.ajce.20221005.13

    Copy | Download

    AMA Style

    Hamka Hamka Adolphe Claudel, Djomi Rolland, Mveh Chantal Marguerite, Tchotang Theodore, Touani Chualeu Parfait, et al. Study of Clay Soils, Case of Nomayos-Cameroon: Thermophysical and Chemicomechanical Characterization of Clay Bricks Loaded with 30% Palm Kernel Shell Powder. Am J Civ Eng. 2022;10(5):191-200. doi: 10.11648/j.ajce.20221005.13

    Copy | Download

  • @article{10.11648/j.ajce.20221005.13,
      author = {Hamka Hamka Adolphe Claudel and Djomi Rolland and Mveh Chantal Marguerite and Tchotang Theodore and Touani Chualeu Parfait and Ngohe Ekam Paul Salomon},
      title = {Study of Clay Soils, Case of Nomayos-Cameroon: Thermophysical and Chemicomechanical Characterization of Clay Bricks Loaded with 30% Palm Kernel Shell Powder},
      journal = {American Journal of Civil Engineering},
      volume = {10},
      number = {5},
      pages = {191-200},
      doi = {10.11648/j.ajce.20221005.13},
      url = {https://doi.org/10.11648/j.ajce.20221005.13},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajce.20221005.13},
      abstract = {The work presented in this article consists in demonstrating that the mixture of clay from clay soils and palm nut shell powder is possible for the production of raw clay bricks.  For that, we have made characterizations of the mixture of the powder of shells of palm kernel and the clay resulting from the argillaceous grounds of Nomayos which was the subject of a publication. Then, we made the bricks with 0% of load and with 30% of load that we had characterized physically, chemically, thermally and mechanically. The results of the physical characterization allowed us to conclude that the density of the material decreases when it is loaded with 30% of palm kernel shell powder but increases and improves the resistance to bending and compression for the same percentage of load. For the results of the thermal characterization, the ATG, the DSC and the DTG showed: for the clay brick, the presence of free water, Kaolinite, illite and Quartz in important proportion affirming that this clay is of the kaolinite type. For the shells, the presence of free water, cellulose, and lignin; for the mixture with 30% of palm kernel shell powder, the presence of both free water, Kaolinite, illite, Quartz, cellulose, and lignin showing the presence of both clay and shells in the mixture. For the results of the chemical characterization, FTIR showed: for clay, the presence of adsorption bands at 2931 cm-1 and 2865 cm-1, absorption peaks at 1554 cm-1, 1494 cm-1 and 693 cm-1 and a peak near 1307 cm-1. For the shells, the presence of intensity bands at 2924.39 cm-1, average intensity of the fine band between 1509.08 cm-1 and 1606.26 cm-1, intensity peaks between 1372.10 cm-1 and 1317.91 then 1239.65-1030.05 cm-1. For the clay-shell mixture, the presence of adsorption bands at 2931 cm-1 and 2865 cm-1 corresponding to asymmetric and symmetric elongation vibrations of the -CH2 groups showing the presence of the clay silane. The peaks of intensity between 1239.65 and 1030.05 cm-1 can be attributed to the -C-O groups of alcohols, Esther, ether, amorphous silica or -C-O bonds of celluloses and lignins showing the presence of the shells in the mixture.},
     year = {2022}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Study of Clay Soils, Case of Nomayos-Cameroon: Thermophysical and Chemicomechanical Characterization of Clay Bricks Loaded with 30% Palm Kernel Shell Powder
    AU  - Hamka Hamka Adolphe Claudel
    AU  - Djomi Rolland
    AU  - Mveh Chantal Marguerite
    AU  - Tchotang Theodore
    AU  - Touani Chualeu Parfait
    AU  - Ngohe Ekam Paul Salomon
    Y1  - 2022/10/11
    PY  - 2022
    N1  - https://doi.org/10.11648/j.ajce.20221005.13
    DO  - 10.11648/j.ajce.20221005.13
    T2  - American Journal of Civil Engineering
    JF  - American Journal of Civil Engineering
    JO  - American Journal of Civil Engineering
    SP  - 191
    EP  - 200
    PB  - Science Publishing Group
    SN  - 2330-8737
    UR  - https://doi.org/10.11648/j.ajce.20221005.13
    AB  - The work presented in this article consists in demonstrating that the mixture of clay from clay soils and palm nut shell powder is possible for the production of raw clay bricks.  For that, we have made characterizations of the mixture of the powder of shells of palm kernel and the clay resulting from the argillaceous grounds of Nomayos which was the subject of a publication. Then, we made the bricks with 0% of load and with 30% of load that we had characterized physically, chemically, thermally and mechanically. The results of the physical characterization allowed us to conclude that the density of the material decreases when it is loaded with 30% of palm kernel shell powder but increases and improves the resistance to bending and compression for the same percentage of load. For the results of the thermal characterization, the ATG, the DSC and the DTG showed: for the clay brick, the presence of free water, Kaolinite, illite and Quartz in important proportion affirming that this clay is of the kaolinite type. For the shells, the presence of free water, cellulose, and lignin; for the mixture with 30% of palm kernel shell powder, the presence of both free water, Kaolinite, illite, Quartz, cellulose, and lignin showing the presence of both clay and shells in the mixture. For the results of the chemical characterization, FTIR showed: for clay, the presence of adsorption bands at 2931 cm-1 and 2865 cm-1, absorption peaks at 1554 cm-1, 1494 cm-1 and 693 cm-1 and a peak near 1307 cm-1. For the shells, the presence of intensity bands at 2924.39 cm-1, average intensity of the fine band between 1509.08 cm-1 and 1606.26 cm-1, intensity peaks between 1372.10 cm-1 and 1317.91 then 1239.65-1030.05 cm-1. For the clay-shell mixture, the presence of adsorption bands at 2931 cm-1 and 2865 cm-1 corresponding to asymmetric and symmetric elongation vibrations of the -CH2 groups showing the presence of the clay silane. The peaks of intensity between 1239.65 and 1030.05 cm-1 can be attributed to the -C-O groups of alcohols, Esther, ether, amorphous silica or -C-O bonds of celluloses and lignins showing the presence of the shells in the mixture.
    VL  - 10
    IS  - 5
    ER  - 

    Copy | Download

Author Information
  • Civil and Mechanical Engineering Laboratory, National Advanced School of Engineering, University of Yaounde I, Yaounde, Cameroon

  • Civil and Mechanical Engineering Laboratory, National Advanced School of Engineering, University of Yaounde I, Yaounde, Cameroon

  • Applied Computer Science Laboratory, National Advanced School of Engineering, University of Yaounde I, Yaounde, Cameroon

  • Civil and Mechanical Engineering Laboratory, National Advanced School of Engineering, University of Yaounde I, Yaounde, Cameroon

  • Civil and Mechanical Engineering Laboratory, National Advanced School of Engineering, University of Yaounde I, Yaounde, Cameroon

  • Energetics Laboratory, National Advanced School of Engineering, University of Yaounde I, Yaounde, Cameroon

  • Sections