| Peer-Reviewed

Parametric Study of the Lateral Behavior of Cast in Drilled Hole Piles

Received: 8 July 2016     Accepted: 18 July 2016     Published: 15 August 2016
Views:       Downloads:
Abstract

A cast in drilled hole (CIDH) piles are to be used as a bridge foundation. The geotechnical data of the site indicate that the soil profile consist of 10m normally consolidated soft clay underlined by a thick layer of over consolidated stiff clay. Three different pile diameters of 1.6m, 1.8m and 2m are selected from the analysis to be used for a depth of 30m below ground level and an average height of 5m above ground level. To investigate behavior of these (CIDH) piles under lateral loads, an analytical parametric study is performed to evaluate the ultimate lateral load capacity of the piles (which is assumed to cause a pile head displacement of 10% of the pile diameter) and the distribution of shear force and bending moment along the depth of the piles. The soil is represented by two ways, linear and nonlinear material. For the linear case, a linear brick finite element is used to represent the soil with either a linearly variable modulus of elasticity from ground level to the bottom of the pile or a constant modulus of elasticity for the top 10 meters (the soft clay) while linearly varying for the next 20m. For the nonlinear case, the P-Y curves method is used to represent the soil by nonlinear springs at intervals of 1 meter. In both cases (linear and nonlinear soil), the piles are assumed to behave linearly. Results obtained indicate that the ultimate lateral load capacity of the piles from the nonlinear case is in the range of 50% to 60% of the linear case.

Published in American Journal of Civil Engineering (Volume 4, Issue 5)
DOI 10.11648/j.ajce.20160405.16
Page(s) 247-253
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2016. Published by Science Publishing Group

Keywords

Cast in Drilled Hole Piles, P-Y Curves, Finite Element

References
[1] Anderson, J., Townsend, F., and Grajales, B., 2003. Case history evaluation of laterally loaded piles. Journal of Geotechnical Geoenvironmental Engineering, ASCE, 129, 187-196.
[2] Banerjee, P. K. and Davis, T. G., 1978. The behavior of axially and laterally loaded single piles embedded in nomohomogeneous soils. Geotechnique, 28, No. 3, 309-326.
[3] Basu, D., and Salgado, R., 2007. Elastic analysis of laterally loaded pile in multilayered soil. Geomechanics Geoengineering, 2, 183-196.
[4] Basu, D., and Salgado, R., 2008. Analysis of laterally loaded piles with rectangular cross sections embedded in layered soil medial. International Journal for Numerical Analysis Methods in Geomechanics. 32, 721-744.
[5] Bransby, M. F., 1999. Selection of p-y curves for the design of single laterally loaded piles. International Journal for Numerical Analysis Methods in Geomechanics, 23, 1909-1926.
[6] Brinch Hansen, J., 1961. The ultimate resistance of rigid piles against transversal forces. Bulletin no. 12. Danish Geotechnical Institute, Copenhagen, Denmark 5-9.
[7] Broms, B., 1964. Lateral Resistance of Piles in Cohesiveness soils. Journal of Soil Mechanics and Foundation Division 90 (4), 27-63.
[8] Brown, D. A., Shie, C. and Kumar, M., 1989. P-y curves for laterally loaded piles derived from three dimensional finite element model. Numerical Models in Geomechanics, NUMOG III, 683-690 (Elisevier Applied Science).
[9] Brown, D. A., Shie, C. F., 1991. Some numerical experiments with a three-dimensional finite element model of laterally loaded piles. Computer and Geotechnics 12, 149-162.
[10] Budhu, M. and Davis, T. G., 1988. Analysis of laterally loaded piles in soft clays. Journal of Geotechnical Engineering Division. ASCE, 114, 21-39.
[11] Desai, C. S. and Appel G. C., 1976. 3-D analysis of laterally loaded structures. Numerical Methods in Geomechanics, Vol. 2, 405-418.
[12] Dewaikar, D. M., Salimath, R. S. and Swant, V. A., 2009. A modified p-y curve for the analysis of laterally loaded pile in stiff clay. Australian Geotechnics Journal volume 44 No. 3, 91-99.
[13] Guo, W. D. and Lee, F. H., 2001. Load transfer approach for laterally loaded piles. International Journal for Numerical Analysis Methods in Geomechanics, 25, 1101-1129.
[14] Jeong, S. S., Seo, D. H., 2004. Analysis of tieback walls using proposed p-y curves for coupled soil springs. Computer and Geotechnics. 31, 443-456.
[15] Jeremic, B., Yang, Z., 2002. Numerical analysis of pile behavior under lateral loads in layered elastic-plastic soils. International Journal for Numerical and Analytical Methods in Geotechnics 26, 1385-1406.
[16] Klar, A. and Frydman, S., 2002. Three-dimensional analysis of lateral pile response using two-dimensional explicit numerical scheme. Journal of Geotechnical Geoenvironmental Engineering. ASCE, 128, 775-784.
[17] Langer, A., Mosley, E. T., and Thompson, C., 1984. Laterally loaded deep foundations: Analysis and performance. ASTM STP 835, 239-243.
[18] Lee, S. L., Kog, Y. C. and Karunaratne, G. P., 1987. Laterally loaded piles in layered soil. Soils and Foundations, 27, 1-10.
[19] Matlock, H., 1970. Correlations for design of laterally loaded piles in clay. Paper no. OTC 1204, in: Proceedings of Second Annual Offshore Technology Conference, Houston, Texas, Vol. 1, 577-594.
[20] Ng, C. W. W. and Zhang, L. M., 2001. Three-dimensional analysis performance of laterally loaded sleeved piles in sloping ground. Journal of Geotechnical Geoenvironmental Engineering, ASCE, 127, 499-509.
[21] O'Neill, M. W., Gazioglu, S. M., 1984. Evaluation of p-y relationships in cohesive soils. Proceedings of a Analysis and Design of Pile Foundations, Geotechnical Engineering Division, 192-213.
[22] Poulos, G. and Davis, H., 1980. Pile Foundation Analysis and Design, John Wiely & sons, Inc., New York.
[23] Poulos, H. G., 1971a. Behavior of laterally loaded piles: I- single piles. Journal of Solid Mechanics, Foundation Division, ASCE, 97, 711-731.
[24] Poulos, H. G., 1971b. Behavior of laterally loaded piles: III- socketed piles. Journal of Solid Mechanics, Foundation Division, ASCE, 98, 341-360.
[25] Pyke, R. and Beikae, M., 1984. A new solution for the resistance of single piles to lateral loading. Laterally Loaded Deep Foundations, ASTM STP 835, 3-20.
[26] Randolph, M. F., 1981. The response of flexible piles to lateral loading. Geotechnique, 31, No. 2, 247-259.
[27] Reese, C. and Matlock, H., 2956. Non-dimensional solutions for laterally loaded piles with soil modulus assumed proportional to depth. The 8th Texas Conference on Soil Mechanics and Foundation Engineering. Austin, 1-41.
[28] Reese, L. C. and Cox, W. R., 1969. Soil behavior from analysis of tests of uninstrumented piles under lateral loading. Performance of Deep Foundations, ASTM STP 444, 160-176.
[29] Reese, L. C. and Van Impe, W. F., 2001. Single pile and pile groups under lateral loading (A. A. Balkema: Rotterdam, Netherland).
[30] Reese, L. C., Cox, W. R. and Koop, F. D., 1974. Analysis of laterally loaded piles in sand. Proceedings of 6th Offshore Technical Conference, Houston, Texas, volume 2, 473-483.
[31] Reese, L. C., Cox, W. R. and Koop, F. D., 1975. Field testing and analysis of laterally loaded piles in stiff clay. Proceedings of 7th Offshore Technical Conference, Houston, Texas, volume 2, 671-690.
[32] Reese, L. C., 1983. Behavior of piles and pile groups under lateral loads. Rep. to the U.S. Dept. of Transportation. Federal Highway Administration, Office of Research, Development, and Technology, Washington, D. C.
[33] Robert, D. Cook, 1995. Finite Element Modeling for Stress Analysis, 1st Ed. USA: John Wiely and Sons.
[34] Sun, K., 1994. Laterally loaded piles in elastic media. Journal of Geotechnical Engineering, ASCE, 120, 1324-1344.
[35] Tak Kim, B., Kim, N., Jin Lee, W., and Su Kim, Y., 2004. Experimental load-transfer curves of laterally loaded piles in Nak-Dong River sand. Journal of Geotechnical Geoenvironmental Engineering, ASCE, 130, 416-425.
[36] Trochanis, A. M., Bielak, J. and Christiano, P., 1991. Three-dimensional nonlinear study of piles. Journal of Geotechnical Engineering, ASCE, 117, 429-447.
[37] USACE, 1998. Design of Deep Foundations: Technical Notes. US Army Corps of Engineers, Engineering Research and Development Center, Washington DC.
[38] Verruijt, A. and Kooijman, A. P., 1989. Laterally loaded piles in layered elastic medium. Geotechnique, 39, No. 1, 39-46.
[39] Wallace, J. W., Tehrani, P. K., Ahlberg, E. R., Stewart, J. P., Taciroglu, E., 2014. Nonlinear load-deflection behavior of reinforced concrete drilled piles in stiff clay. Journal of Geotechnical Geoenvironmental Engineering, ASCE, 140, 1-14.
[40] Won, J. O., You, K. H., Jeong, S. S., Kim, S. i., 2005. Coupled effects in stability analysis of pile slope systems. Computer and Geotechnics 32, 304-315.
[41] Yan, L., and Bryne, P. M., 1992. Lateral pile response to monotonic pile head loading. Canadian Geotechnical Journal, 29 (6), 955-970.
Cite This Article
  • APA Style

    Samir Abdul Baki Jabbar Al-Jassim, Rafi Mohammed Qasim. (2016). Parametric Study of the Lateral Behavior of Cast in Drilled Hole Piles. American Journal of Civil Engineering, 4(5), 247-253. https://doi.org/10.11648/j.ajce.20160405.16

    Copy | Download

    ACS Style

    Samir Abdul Baki Jabbar Al-Jassim; Rafi Mohammed Qasim. Parametric Study of the Lateral Behavior of Cast in Drilled Hole Piles. Am. J. Civ. Eng. 2016, 4(5), 247-253. doi: 10.11648/j.ajce.20160405.16

    Copy | Download

    AMA Style

    Samir Abdul Baki Jabbar Al-Jassim, Rafi Mohammed Qasim. Parametric Study of the Lateral Behavior of Cast in Drilled Hole Piles. Am J Civ Eng. 2016;4(5):247-253. doi: 10.11648/j.ajce.20160405.16

    Copy | Download

  • @article{10.11648/j.ajce.20160405.16,
      author = {Samir Abdul Baki Jabbar Al-Jassim and Rafi Mohammed Qasim},
      title = {Parametric Study of the Lateral Behavior of Cast in Drilled Hole Piles},
      journal = {American Journal of Civil Engineering},
      volume = {4},
      number = {5},
      pages = {247-253},
      doi = {10.11648/j.ajce.20160405.16},
      url = {https://doi.org/10.11648/j.ajce.20160405.16},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajce.20160405.16},
      abstract = {A cast in drilled hole (CIDH) piles are to be used as a bridge foundation. The geotechnical data of the site indicate that the soil profile consist of 10m normally consolidated soft clay underlined by a thick layer of over consolidated stiff clay. Three different pile diameters of 1.6m, 1.8m and 2m are selected from the analysis to be used for a depth of 30m below ground level and an average height of 5m above ground level. To investigate behavior of these (CIDH) piles under lateral loads, an analytical parametric study is performed to evaluate the ultimate lateral load capacity of the piles (which is assumed to cause a pile head displacement of 10% of the pile diameter) and the distribution of shear force and bending moment along the depth of the piles. The soil is represented by two ways, linear and nonlinear material. For the linear case, a linear brick finite element is used to represent the soil with either a linearly variable modulus of elasticity from ground level to the bottom of the pile or a constant modulus of elasticity for the top 10 meters (the soft clay) while linearly varying for the next 20m. For the nonlinear case, the P-Y curves method is used to represent the soil by nonlinear springs at intervals of 1 meter. In both cases (linear and nonlinear soil), the piles are assumed to behave linearly. Results obtained indicate that the ultimate lateral load capacity of the piles from the nonlinear case is in the range of 50% to 60% of the linear case.},
     year = {2016}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Parametric Study of the Lateral Behavior of Cast in Drilled Hole Piles
    AU  - Samir Abdul Baki Jabbar Al-Jassim
    AU  - Rafi Mohammed Qasim
    Y1  - 2016/08/15
    PY  - 2016
    N1  - https://doi.org/10.11648/j.ajce.20160405.16
    DO  - 10.11648/j.ajce.20160405.16
    T2  - American Journal of Civil Engineering
    JF  - American Journal of Civil Engineering
    JO  - American Journal of Civil Engineering
    SP  - 247
    EP  - 253
    PB  - Science Publishing Group
    SN  - 2330-8737
    UR  - https://doi.org/10.11648/j.ajce.20160405.16
    AB  - A cast in drilled hole (CIDH) piles are to be used as a bridge foundation. The geotechnical data of the site indicate that the soil profile consist of 10m normally consolidated soft clay underlined by a thick layer of over consolidated stiff clay. Three different pile diameters of 1.6m, 1.8m and 2m are selected from the analysis to be used for a depth of 30m below ground level and an average height of 5m above ground level. To investigate behavior of these (CIDH) piles under lateral loads, an analytical parametric study is performed to evaluate the ultimate lateral load capacity of the piles (which is assumed to cause a pile head displacement of 10% of the pile diameter) and the distribution of shear force and bending moment along the depth of the piles. The soil is represented by two ways, linear and nonlinear material. For the linear case, a linear brick finite element is used to represent the soil with either a linearly variable modulus of elasticity from ground level to the bottom of the pile or a constant modulus of elasticity for the top 10 meters (the soft clay) while linearly varying for the next 20m. For the nonlinear case, the P-Y curves method is used to represent the soil by nonlinear springs at intervals of 1 meter. In both cases (linear and nonlinear soil), the piles are assumed to behave linearly. Results obtained indicate that the ultimate lateral load capacity of the piles from the nonlinear case is in the range of 50% to 60% of the linear case.
    VL  - 4
    IS  - 5
    ER  - 

    Copy | Download

Author Information
  • Department of Civil Engineering, University of Basra, Basra, Iraq

  • Department of Environment and Pollution Engineering, Basra Engineering Technical College, Southern Technical University, Basra, Iraq

  • Sections